Track Price :: Reviewing Millions of Products!

BN-180 GPS Module UART TTL Dual Glonass GPS Car Navigation with GPS Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D F3 Flight Controller Geekstory
BN-180 GPS Module UART TTL Dual Glonass GPS Car Navigation with GPS Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D F3 Flight Controller Geekstory
Disclaimer: As an Amazon Associate I may earn from qualifying purchases

Description
 Dimension :18mm*18mm*6mm
Weight : 4.9g
Connector : 1.00mm spacing between the 4pins patch seat

Specification
 Receiving Format :　GPS,GLONASS,Galileo,BeiDou,QZSS and SBA...

Buy Now From Amazon

Product Review

Description
 Dimension :18mm*18mm*6mm
Weight : 4.9g
Connector : 1.00mm spacing between the 4pins patch seat

Specification
 Receiving Format :　GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS
Frequency : GPS L1,GLONASS L1,BeiDou B1,SBAS L1,Galileo E1
Channels : 72 Searching Channel

Sensitivity
Tracking : -167dBm
Reacquisition : -160dBm
Cold start : -148dBm
Hot start : -156dBm

Accuracy
Position Horizontal : 2.0 m CEP 2D RMS SBAS Enable (Typical Open Sky)
Velocity : 0.1m/sec 95% (SA off)
Timing : 1us synchronized to GPS time

Acquisition Time
Cold Start : 26s
Warm start : 25s
Hot start : 1s

Data and Update Rate
Support Rate : 4800bps to 921600bps,Default 9600bps
Data Level : TTL or RS-232,Default TTL level
Data Protocol : NMEA-0183 or UBX, Default NMEA-0183
Single GNSS : 1Hz-18Hz
Concurrent GNSS : 1Hz-10Hz,Default 1Hz

Operational Limits
Altitude : 50,000m Max
Velocity : 515m/s Max
Acceleration : Less than 4g

Power consumption
VCC : DC Voltage 3.0V-5.5V,Typical: 5.0V
Current : Capture 50mA/5.0V
Operating temp :　-40 °C ~ +85°C
Storage Temp : -40°C ~ +105°C

Indicator :
TX LED:blue.The data output, TX LED flashing
PPS LED:red.PPS LED not bright when GPS not fixed,flashing when fixed

Wiring:
GND,TX output,RX input,VCC(3.0v-5.5v)

Package Included
1 x BN-180 GPS Module
2 x 15cm Cable

  • This BN-180 GPS Module can show your speed. When you use it for Raspberry Pi, there is no driver needed. Here is connection with RPi, red to 3.3v, black to gnd, green to txd, white to rxd
  • The TX LED flash means gps module output normally. The PPS LED flash means gps module locate your place
  • Data Level : TTL or RS-232, Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
  • This BN-180 GPS Module does not have FLASH and cannot be saved. 72 Searching Channel Support Rate : 4800bps to 921600bps, Default 9600bps
  • What you will get: 1 X BN-180 GPS Module

Similar Products

Geekstory Beitian BN-880 GPS Module U8 with Flash HMC5883 Compass + GPS Active Antenna Support GPS Glonass Beidou Car Navigation for Arduino Raspberry Pi Aircraft Pixhawk APM Flight ControllerTeam BlackSheep TBS Crossfire Nano RXFrSky R-XSR Ultra SBUS/CPPM D16 16CH Mini Redundancy Receiver 1.5g for RC Multirotor FPV Racing DroneBeitian BN-220 Dual GPS Glonass Module Navigation TTL Level 9600bps + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Flight Control GeekstoryMG Chemicals 422B Silicone Modified Conformal Coating, 55 ml BottleEUDAX FPV Black Sponge Mat Landing Skid Pad Gear Anti-Vibration Shockproof Foam Sticky Tape for rc multirotor Quadcopter Racing Copter Drone Mini-Quad (60 Pcs)NIDICI BN-880 Flight Control GPS Module Dual Module Compass with Cable for RC Drone FPV RacingAKK X2-Ultimate 5.8GHz 0.01mW/25mW/200mW/600mW/1000mW Switchable FPV Transmitter Compatible with Betaflight OSD FC Configuring Upgraded Long Range VersionMatek F411-WING Flight Controller F4 FC Built-in OSD BEC & Current Sensor on Board for RC FPV Racing DroneiFlight 10pcs Plastic Protection Antenna Tube with Caps for FRSKY XM XM+ X4R X4RSB S6R/D Series/TF Series IPEX4 Receiver Antenna (Black)
Copyright © 2021 Track Price - All rights reserved